How to Enable ISTA+ V4.11 Expert Mode for Single Module Programming

Does anyone have a solution for Ista+ Programming Expert Mode?
No expert mode available yet for ISTA+ v4.11.12.

This will be an issue in feature, expert mode can get you out of unpleasant work.

For example if you update i update a whole g11 with ista p and if you update kafas you lose fsc codes, so if i deselected kafas, fsc stayed unharmed. But you can do that now with BMW ISTA Software

One more important remark is that esys wont let you update a module that is allready updated, but ista let you do it, so after 7/11 psdzdate you are stuck with this issue too…

Best to use a router for programming HUH etc through ista
Or you can just use tftpd32 (or tftpd64 if 64bit OS)
Update: ISTA+ 4.12.12 has the expert mode – Confirmed!

ista-p-expert-mode-1
ista-p-expert-mode-2
ista-p-expert-mode-3
ista-p-expert-mode-4
ista-p-expert-mode-5
ista-p-expert-mode-6

Note that Ista+ expert mode is Ista P expert mode

siat-p-ista+-4

The difference between Expert mode and Ista plus?

The difference is his loader allows for hiding of modules

Ista plus does not he or someone may be working on an alternate loader to hide retrofitted modules but as it so far look into ESYS for that only option I can think of right now last istap that had a lot a F ,G or I cars was 3.64.2 as 3.65.0 only had like 2 model forget exactly which ones you have to double or make link dos command to point to istaplus PSdZ folder

Some new solutions to activate ISTA-P expert mode ?

so updating the folders in ISTA-P with the files from PSdz swe will not do the trick. You will be inserting back all the missing vehicles. I saw in the main series you will have to rename F, G, I series files to reflect.

after copy PSDz (data_swi) to pszdata ISTA P with correction data in mainseries, add data F001, F10,…etc = same result

ISTA P shows window that car is not programmable (only ISTA+)
trick is somewhere else
this is Ista p expert mode confirmed to work 100%

Why not just use a earlier version of ISTA-P (such as 4.08 or 4.10) to do single module coding?
Because what i am getting is there are problematic files out there that BMW knows about and in the latest version of ISTA+ it can stop from a certain update and keep the module on the one that works. So could you not reverse populate for example take the p-files from a later version to a previous but you would need all files and folders for example. anyone with more can chime in

Anyone has good success with Ista P expert mode?
Yep. Have tested Expert Mode on BMW e66
Here is the details…
Select Create new session. Click on Select ISTA/P server automatically. Click on Continue.
ista-p-Expert-Mode-BMW-E66-1

Click on ICOM Next/ICOM A2 emulator & Connect to continue.
ista-p-Expert-Mode-BMW-E66-2

Connecting…

Click on on the 4th button at the top, to get the information of Connection manager, then close that interface.

Determining model series…(E66)

Data being checked…

Checking vehicle identification number…(DE97243)

Control unit replaced?

Click on No, and also click on “Before starting vehicle programming…” click on Next.

ista-p-Expert-Mode-BMW-E66-3

Control unit change over.

ista-p-Expert-Mode-BMW-E66-4
Determining…

Identifying fitted control units…

Determining target context…

Calculating measure plan…

Go to Control unit tree, and select ZGM.

ista-p-Expert-Mode-BMW-E66-5
Edit plan show as follows:

ista-p-Expert-Mode-BMW-E66-6

Go to Immediate measures.

Click on Hide all actions.
ista-p-Expert-Mode-BMW-E66-7

Go to Edit plan. No cross on Program P. Then close it.
ista-p-Expert-Mode-BMW-E66-8

Select SZL.

ista-p-Expert-Mode-BMW-E66-9

Edit plan show as follows:

ista-p-Expert-Mode-BMW-E66-10

Go to Immediate measures.

Click on Hide all actions.

Back to Edit plan. No cross there. Then close it.

ista-p-Expert-Mode-BMW-E66-11

Done!

How to solved the problem with ISTA and BMW m3 e36 of 96

Car model and year:
BMW m3 e36 of 96

BMW diagnostic software to consider to use:
ISTA + 3.53
Inpa cable

Problem:
From now on it is necessary to put the cursor of the interface on the D or the K knowing that it is of 96.
I say DKan
Then I plug everything I run ista it takes me the characteristics of my vehicle
After when I go to expert mode to diagnose the DME and well it makes me no fault find it seemed weird so I unplug the debimettre to see if it captures the defect and well no fault so I tell myself that there is a concern for dialogue.

How-to-solved-the-problem-with-ISTA-and-BMW-1
How-to-solved-the-problem-with-ISTA-and-BMW-2

Tips to follow:
To make an E36 you have to enter the chassis manually, ISTA will not detect the box tree and then have to switch to the old DIS style visual.

Q: to see and control the versions, simply click on the adjustable wrench, top tool bar, then select “version” and you have your answer for a diag on E36, are you sure he found your DME ??
A: When I plug it in, I open it ista then I do the necessary it happens to find the characteristics of my vehicle m3 e36 and when I try to go further diag box it finds nothing
I will repeat the test in the week and see exactly all the steps.

Q: everything depends on whether it is a phase 1 or 2, phase1 = ADS protocol / phase2 = ODB protocol in this case ISTA works phase 1 / DIS or INPA see Carsoft 6.5
A: It is a m3 e36 of 96 phase 1

Q: for ista it is missed, it must go through DIS and head gt1, or Carsoft 6.5 with its interface.
A: I have a friend who has a m3 e36 also in phase 1 and he also has the ista but not on the computer like me and it works but as he lives far from home we can not try on mine or his

Q: not on a pc ?? what is it like support you are sure that it uses ISTA on the other hand it is possible that it has a limp bosch, the variation is of the Siemens, one of the 2 is not recognized
A: That’s what he has but I’m not using it
Mine is on pc with a cable dcan / blue kcan plus the intermediate round plug

How-to-solved-the-problem-with-ISTA-and-BMW-3
How-to-solved-the-problem-with-ISTA-and-BMW-4

Tip 1:
No M3 E36 3.2 Phase1 = E36 Phase 2

1996 = ODB and no ads

M3 E36 3.0 L = ADS

So it must work very well with BMW Diagnostic Tool ISTA

I had a M3 E36 3.2 Phase1 of 1995, so the very first E36 Phase 2 and it worked very well.

Tip 2:
the m3 e36 3litre it is a s50 driven by a Bosch in ADS unlike the e36 m3 3.2 which is on a s50 driven by siemens so obd, he cannot diag the engine with the cable dcan mode kcan on the take oBD

the ADS protocol (DS1) uses two communication channels (TX / K and RX / L), it requires a specific interface, the round with 20 plug.

e36 before about 95: ADS / DS1 protocol on most modules except some “OBD” modules: ABS, AIRBAG
e36 after about 95: OBD / DS2 protocol on most modules, all engine computers except diesel td and tds remaining in ADS for DMEs, Bosch calculators are in ADS and Siemens in OBD

Different between INPA and ICOM?

INPA just need a OBD II cable with any PC and it can run. Software can be download. The cable cost only $20 USD + cost of a laptop.For a ICOM Scanner, it need a software called ISTA. I know all the bmw model can be used with. The whole system cost around $400 USD + cost of laptop. Anyone know the different between them??? If I am just a user and do some simple work for my E60 M5 (SMG clutch teach-in) , look for error codes. Which one I should buy?

ICOM and GT1 are hardware. GT1 was the previous generation, then came ICOM, and now something called E-NET (I believe).

DIS, ISTA, and INPA are software. DIS was the first generation. ISTA is the replacement for DIS. INPA is software, but was designed for BMW engineer use, not dealerships and most dealerships don’t have it or any clue how to use it. Some of the other guys here can recommend a software set, it seems the place I got mine is no longer selling them either.

ICOM is probably best for me. It does work with 20-pin port “ADS” fully.

Regarding ADS another question/problem came in my mind. Afaik ADS is only supported by Ediabas 6.4.3 and 6.4.7. Is there any advise how to handle this? Or is the only way having 6.4.3 or 6.4.7 installed on one machine and 7.3.0 on another? Is it at all necessary to use a newer version than 6.4.3 of ediabas for newer cars? Currenty I run 7.3.0 because I do not have a ADS interface.

The old EDIABAS is for when using an actual physical ADS interface. Keep using 7.3.0, it will need to be configured as “remote” and you will have to input the IP address of the BMW ICOM A2.You will need 2 tools. iTool Radar to get IP of ICOM and Reserve ICOM (only for when you use INPA, WinKFP, NCSExpert, etc), and EasyConnect for easy configuration of your ediabas.ini file.

how to distinguish the original bmw icom A2 software and fake ICOM A2

BMW ICOM A2+B+C is the best diagnostic tool for BMW car.
1. Super version BMW ICOM A2+B+C is compatible with many kinds of computers.
2. Once insert hard disk into your computer it can automatically install.
3. No request on computer system, and no time limiation for use.

15-1 15-2

Q: Is it possible, that I change the Language? There Is only english in Black letters
A: Hello, please open the software first, click “Reset Settings”, then restart the software again, the language option will be available
BMW ICOM language setting

15-3

Q: I tried installing Bmw Icom in the notebook computer “Lenovo”, when I turned on the computer with the new hard drive asks me 2 passwords
can you tell me what they are?
A: First password is “BMW”, second password just ignore, do not need to fill anything.

Q:Does your bmw icom has esys software?
A:yes,it has,It is engineer version HDD.

How to Solve BMW ISTA+ 4.1 “Programming is not possible”

BMW ISTA+ for BMW diagnostic & programming function, BMW ISTA+ software compatible with BMW ICOM A2ICOM Next & Enet cable, recently some users to help those with error “Programming is not possible” when using BMW ISTA+. Eobdtool.com share How to Solve BMW ISTA+ 4.1 “Programming is not possible” as following.

Rheingold ISTA+ BMW Diagnostic Software BMW ISTA D/P software 2018.03 Version

Here obd2tool.com share lists possible solutions as follows:

Sw version: Ista+ 4.10.30
Hw: Enet cable

25-1

Error message: I get message after reading all ECU’s
“Programming is not possible”
If I click this message away I can just continue.

I have: bin, binx64, host, hostx64
But which files/maps must be located in map PSdZ?

Solution 1:

Try it with the BLP data so the folder “data” under C / Rheingold / PSdZ / data ..
Of course, in the Reg also specify that the data is available but still as you have made everything on “false” ..

you unpack the BLP under C / Rheingold / PSdZ / and you get the folder “data” ..
So C / Rheingold / PSdZ / data ..

Reg:

“Product Version” = “4.10.30.15635”
“Main Product Version” = “4.10”
“Data version” = “10/04/31”
“DataVersion_en-GB” “04/10/31”
“Logistic Base Version” “10/04/30”
“SWIData” = “04/10/30”

“BMW.Rheingold.Programming.ExpertMode” “True”
“BMW.Rheingold.Programming.Enabled” = “True”
“BMW.Rheingold.Programming.PsdzDataPath” = “.. \\ .. \\ .. \\ \\ PSdZ data_swi”

If it doesn’t work, try the following solution. It works for bmw a2 in earlier version.

Solution 2:

In earlier versions this worked:
“BMW.Rheingold.Programming.ExpertMode”=”False”
“BMW.Rheingold.Programming.Enabled”=”False”
“BMW.Rheingold.Programming.PsdzDataPath”=”..\\..\\PSdZ\\data”

Have not tried on latest.

P.S. BLP must be installed normally into data folder. No need to create any empty folders.

Still had psdz path set to data_swi. You must adjust it to be data instead of data_swi when no sdp installed. Then it should not complain and work. BMW ICOM BLP data MUST be installed in all cases.

Solution 3:

Create empty folders
С:\Rheingold\PSdZ\data
С:\Rheingold\PSdZ\data_swi

Working registry

Windows Registry Editor Version 5.00

[HKEY_LOCAL_MACHINE\SOFTWARE\WOW6432Node\BMWGroup]

[HKEY_LOCAL_MACHINE\SOFTWARE\WOW6432Node\BMWGroup\ISPI]

[HKEY_LOCAL_MACHINE\SOFTWARE\WOW6432Node\BMWGroup\ISPI\ISTA]
“DataVersion”=”4.10.31”
“DataVersion_en-GB”=”4.10.31”
“ProductVersion”=”4.10.30.15635”
“MainProductVersion”=”4.10”
“InstallLocation”=”C:\\Rheingold”
“LogisticBaseVersion”=”4.10.30”
“SWIData”=”4.10.30”

[HKEY_LOCAL_MACHINE\SOFTWARE\WOW6432Node\BMWGroup\ISPI\Rheingold]
“BMW.Rheingold.Programming.Enabled”=”True”
“BMW.Rheingold.Programming.PsdzDataPath”=”..\\..\\..\\PSdZ\\data_swi”
“BMW.Rheingold.Programming.ExpertMode”=”True”

Rheingold location
Directory of c:\Rheingold\PSdZ

06-Apr-18 22:13 <DIR> .
06-Apr-18 22:13 <DIR> ..
29-Mar-18 19:35 <DIR> bin
29-Mar-18 19:35 <DIR> binx64
06-Apr-18 22:13 <DIR> data
16-Mar-18 09:25 <DIR> data_swi
29-Mar-18 19:35 <DIR> host
29-Mar-18 19:35 <DIR> hostx64

FULL SW
Directory of c:\Rheingold\PSdZ\data_swi

16-Mar-18 09:25 <DIR> .
16-Mar-18 09:25 <DIR> ..
16-Mar-18 09:52 <DIR> psdzdata

Lite SW
Directory of c:\Rheingold\PSdZ\data

06-Apr-18 22:13 <DIR> .
06-Apr-18 22:13 <DIR> ..
06-Apr-18 22:13 <DIR> psdzdata

Need purchase the Rheingold BMW ISTA+ BMW Diagnostic & Programming function just contact us freely.