All Benz diagnostic and programming Benz Ecom VS SD C4

New Arrival: Benz Ecom diagnostic and programming tool for newest Benz models. It comes with Dongle and software in the hard disk, activation via remote assistance. Works with newest Benz models instead of old models like MB SD C4.

1.Ecom
Support diagnostic software Xentry, engineering software Vediamo and super DTS Monaco,  it has a than higher access right than SDC4.

Ecom supports the CAN/DoIP protocol, which can be used to diagnose and programming (brushing & writing) for the new car audio and video entertainment systems.

The Mercedes-Benz engineering database of diagnosis / coding / retrofit /flashings is using the Xentry database, so the Mercedes-Benz engineering version depends on the version of Xentry, as long as the database is new, the V4.00 version can be used on new models. compact3 can be used.
SDC4 does not support ODX documents. The latest V5.00 uses eCom to support ODX files. It is recommended to use Ecom, with DoIP function, the speed is faster and more stable.

Benz-diagnostic-and-programming-Benz-Ecom-VS-SD-C4-1

2.SD C4
Support the diagnostic software Xentry, DAS software diagnostics, engineering Vediamo,  super DTS Monaco, Xentry and DAS Developer mode etc.

Common Name: Developing Data Engineering Edition After 2010
Version, added a lot of functional restrictions. So everyone will encounter the problem that the vehicle version is too new to enter
the control unit, or entering the control unit and cannot make any special modifications. For example: W204 /212 2012
The instrument is needed to modify the regional language configuration or open other convenient functions. With the increasing number of new car with DoIP protocol, the mb star SDC4 has slowly failed to meet market demand.

Benz-diagnostic-and-programming-Benz-Ecom-VS-SD-C4-2

DTS-Monaco and Vediamo, which better

DTS-monaco and Vediamo are added to MB Star C4 software since 12-2017.
20-1

but what is DTS-monaco and what is Vediamo? And what\s the difference?

Look here:

20-2

What is DTS-monaco:

DTS Monaco is universal Engineering Tester for Diagnostic and Control Functions of Vehicle

ECUs. The name Monaco is derived from Modular Analyzer for Vehicle Communication.

DTS Monaco comprehensively covers all tasks in the areas of engineering, testing and

preparation of manufacturing tests:

*   diagnostics
*   analysis
*   OBD
*   flash programming
*   measuring
*   parameterizing
*   residual bus simulation
*   OTX

MB SD C4 DTS Monaco is based on standards such as ODX, OTX and UDS

20-3

What is Vediamo:

Vediamo Software is used by the plant engineers to develop diagnosis and engineering software, which is now used by Xentry and DAS, is based on the Mercedes Benz super engineering version developed and delivered to the general customer service dealers’ use.

The use of MB super engineering version has no limitation in diagnosis / modification / programming function are open which cannot be through the VEDOC (the original application code changes with flow) can be free to increase or decrease the SA code, modify the objective, for example: the increase of vehicles equipped with SA500 electric folding mirrors, commonly known as the Xentry and DAS development mode: open data project version in 2010 after the release, increase the number of functional limitations. So we will meet the vehicle version is too new to be into the control unit in use, or are unable to do any special modifications to the control unit.

For example: W204/2122012 instrument to modify the area family configuration, or open other resource advantage function. Diagnosis / Mercedes super engineering version of the code with code / modification / programming database using the Xentry database, so the Mercedes Benz super engineering version is determined with the Xentry version, as long as the database is new and can be used in new models.

What’s the difference of DTS-monaco and Vediamo:

20-4
20-5

2018. 03 MB SD Connect C4 C5 Xentry Start Key Activation

Here is the steps to teach you how to activate XENTRY:

Step 1: Double Check the icon name “starkey Center ” which on the computer desktop.
1
2

Record the computer’s Hardware ID
3

Step2: Double Check the folder”TOOLS” which on the computer desktop.
4

Run xentry developer V1.10

5

Step3:
As shown below: Enter the computer’s Hardware ID, Stat Date, Expiration Date. Calculate the license string.
8
7

Step4:Copy licenseto Start keys and save

8
9
10
11

Step5: Run xentry, as follows
12

We can supply Laptop + Software all ready for you.
We can supply FULL package C4 C5 SD + Laptop + Software for you.
We can carry out some C4 C5 SD repairs.
Remote installations available (if you supply the correct HDD size and install the correct Windows OS).
Teamviewer remote support available.

If you are interesting in buy MB Star Diagnostic Tools , Please contact our sales via sales@obd2tool.com

SDconnect C4 connection problem- Das fault (1.1) -1.501.9878

SD Connect C4 fails to connect and comes up with the error message:

Das fault (1.1) -1.501.9878

The mux is connecting, with diagnosis computer both by lan cable or wifi ( passed and respond to all self tests), no lcd problems or blocked (!) . The fault comes when das try to initialize the mux green led blinks about 10 sec,and this fault comes no matter is from das standalone or launched from xentry.

Software & install:

xentry 12.2015 , das bin, blacklist fixed etc on a dell d630 appid 253 and ……

Solutions:

You must change IP address in windows.172.29.127.119:

Go into “Control Panel”, “Network Connection”, “Local Network Connection”> right click > properties > choose this one with TCP/IP, select this, chose properties, choose manually ip, and put this ip “172.29.127.119”, mask 255.255.0.0 (as you will get when type ip), rest of field, leave blank.

if it does not work

Try one more time make update of these 2 package.

6-1