How to use Nissan Consult III do ECU programming

Consult-3-Plus-3
I try to program a new blank engine ECM on a 2013 Nissan Armada. I purchased the software file from Nissan website and one Consult-3 Plus. I do not have Consult online synchronized with Assist. At first, I have no idea what folder to put this file in so Consult program will find.

I used ners and nissan file extracted to correct folders by itself. used unpack.exe. anyway here you go 6) For CONSULT III plus “Blank” ECU (ECM and non-IK TCM) Programming

Note 1: Before using this application, you will need to put the “programming” data file (*.dat) and the management csv file you received with the download, in the C:\ReproProgramming folder (see screen capture

above under item # 5). Without the programming data and the management csv file in this folder, the C-III plus application will not identify or display the applicable programming. The Auto diagnostic tool C-III plus software will check the part number of the ECU on the vehicle and display the reprogram to be installed.

NOTE 2: If this is the first time using C-III plus for reprogramming, you may need to make the C:\ReproProgramming folder. C-III plus does not automatically create the folder.

Cloned GM MDI possible work with Ford IDS software

Is clone GM MDI interface possible to work with Ford IDS without limitations?
Also is there anyway to convert MDI to a VCM II by flashing it? They seem to be very similar. But how to?

Look here and know how mates experienced talk about it…some say yes, some no, some possible…

Reply 1: As i know, GM MDI and Ford IDS are two different scanners.
The GM MDI can’t work with Ford IDS

Reply 2: Possible but not easy…Requires editing of the Dynamic link library files and more.

i have had MDI Working with it for a long time for personal use
Since version 97.xxx it is easier than say 96.01 because when they changed things to block clones in this version, they basically changed the file structure to that of an MDI.

Reply 3: My dilemma is deciding to get rid of my MDI clone that I purchased 1 year ago (I sold my GM car and bought a Ford so I don’t need it anymore) or try to use the gm mdi software on a Ford vehicle. I don’t have the money to purchase a genuine VCM II and I don’t want to buy a clone either.
I just want to update a few things on my Ford since the warranty is over.
I need to update the GPS module and activate the digital speedo. Looks like I’ll just leave it alone before I screw things up.

Reply 4: I have the same mdi and try flash the sd card put it in recovery mode with ford manager and don’t work when I try back to gm the tool never responding again the hardware damage and leds turn on red beeping so I think you sell that mdi and then buy a vxdiag vcx nano for ford I have one and working

Reply 5: There must be a way to flash the FPGA to a VCM. Once that’s done you can probably recovery the SD card.
The SD cards can also be copied using a tool called USB Image Tool so I’m sure you can recover your MDI.
I just don’t want to bother with it because I don’t know if it will work.
I might sell it and buy another clone. I haven’t decided yet. The MDI clone looks so much better than the VCM clone.

Reply 6: GM MDI and Ford VCM II are made by Bosch ETAS as well as Alliance VI+ or as many OEM tools now
But this one are a little bit different architecture.
So as we discussed many times and Nr. Vag Vag already confirmed in the forum you can use VCM II with Tech2Win and GDS2 but not fully
You can use VCM II with Nissan Consult III Plus but also hot full
Well I didn’t checked GM MDI with Ford IDS but I’m very sure tgat you are waisting your time for the moment.
When IDS will cover J2534 tool then you maybe will be happy to us the GM MDI with IDS but for the moment forget about
I changed the SD card in VCM II clone because this one was defective ( so a fresh untouched sd card – just formated ) and I only put it in Recovery Mode and I fix it. But I’m not sure that you can do it the same with a GM MDI.
You can try it.
Good luck

Reply 7: Well I suppose that you need an account/subscription
But if you know what exactly calibration you need you can download it from obd2tool.com
Good luck

Reply 8: Forscan as you can see it can works with a simple tool elm 327 software or with a Passthru J2534 tool
Gm Mdi it is a J2534 tool that’s why is working
Ids is different.

Good luck

How to get Nissan Consult 3 Software to Work with Jdiag Elite J2534

– Is the Jdiag Elite J2534 compatible with Nissan Consult III Plus 2017 the latest software?

– Yes, definitely. It works perfect with Nissan consult III Plus software, already tested with many Nissan cars.

So, how to setup Jdiag Elite J2534 to work with Nissan consult 3 Plus?

Here you go.

The main steps…

Open Consult iii Plus Software on Desktop

Connect JDiag Elite to the laptop USB and OBDII cable to the OBDII port on the car

Choose JDiag hardware

Choose the signal module to read out information

Then work with it

Then the details for you…

Open Nissan Consult 3 Plus software

Connect JDiag Elite J2534 device to the laptop USB and OBDII cable to the OBDII port on the car

Select VI/MI in Consult 3 Plus ver.52.11

nissan-consult-iii-plus-1

Select VI and click on Connect

nissan-consult-iii-plus-2

Then Close

nissan-consult-iii-plus-3

You’ll see the connection status: VI: Normal module/USB connection
nissan-consult-iii-plus-4
Start Diagnosis (one system)

nissan-consult-iii-plus-5

Choose a module to read out info
nissan-consult-iii-plus-6
nissan-consult-iii-plus-7

Also, you can choose by the car type

Back and start Diagnosis (all system)
nissan-consult-iii-plus-8

Consult 3 plus Nissan car list
nissan-consult-iii-plus-9

Consult 3 plus Infiniti car list
nissan-consult-iii-plus-10

Manual selection

Choose a model and the model year
nissan-consult-iii-plus-11
nissan-consult-iii-plus-12
nissan-consult-iii-plus-13

Automatic selection

nissan-consult-iii-plus-14
Enjoy!

Consult-3 Plus for Nissan is the newest Nissan diagnostic tool

Nissan Consult III Plus is the newest Nissan diagnostic tool.
1. Nissan Consult III Plus supports Nissan 2016 MY LEAF Quest and Murano Cross Cabriolet,
2.super racing MY GT-R and 2012 of NV and 2012 MY Infiniti M and M Hybrid from 2011/12.
3.Consult-3 Plus for Nissan= Consult-3 + Consult-2

Consult-3 Plus for Nissan Consult 3 V61.10 diagnostic tool for Nissan from OBD2TOOL
Consult-3 Plus for Nissan= Consult-3 + Consult-2
Software Version: V61.10
C3+ GTR software V20.11
This Consult-3 Plus work for 2016 Nissan
Support Multi-Languages: English, French, German, Portuguese, Italian, Japanese, Finnish, Greek, Russian, Spanish, Turkish, TChinese(Simplified), Chinese(Traditional)
Communication Mode: USB 2.0 / Bluetooth
OS Requirement: Work with Windows XP,WIN7 WIN8 WIN10
Support Electronic control module Programming,If you want to key programming, please buy the Security Card for Immobilizer
V61.10 Software Download: https://mega.nz/#!aUR3BaxB!ZL3WccsZn–wG8xIirSzgqlZiEkgyxDRen9MrugEr-w

Nissan Consult 3 Plus Function:
Consult-3 Plus for Nissan can support all the models of the Nissan and Infiniti from 1996 up till now, with all Consult II & III functions .
And consult III plus can calcaulate the password for the new cars till year 2016 with NISSAN Password.
1. Consult-3 plus (consult 3+) work for all nissan car , infiniti car and for nissan gtr car to 2016.
2. Consult-3 plus work with obd-16 connector for the new kind of car, work with 14 pin connector for the old kind of car.
3. Consult-3 plus support for nissan car electrolic system diagnostic.
4. Consult-3 plus support for nissan electromobiles such as Leaf.
5. Consult-3 plus support all Renault.

Conslu-3 for Nissan Functions:
1. Scantool Diagnostics:for all Nissan,Infiniti,GTR
2. Immobi and Smart key:for all Nissan,Infiniti,GTR
3. Nissan GTR: for Nissan GTR Diagbostics and Immobi
4. Electromobiles car:for Nissan Electromobiles car Diagbostics and Immobi

Conslu-3 for Nissan Packing List:
1pc* Consult 3 Plus for Nissan Vehicle Communication Module + OBD16 Cable
1pc* 14Pin Line for Nissan
1pc* USB 2.0 Cable
1pc* Bluetooth
1pc* Power Supply
1pc* Casebox