How to install DRBIII Emulator for Chrysler wiTech Micropod 2 on Windows 7 Pro 32-bit?

The procedure for installing DRBIII Emulator on Windows 7 Pro 32-bit:

1: Start with a fresh install of Windows 7 Pro 32-bit.


2: Install all the necessary drivers for your laptop.


3: Set the clock to the current date and time. (It didn’t work when set to 01/01/2017)


4: Connect to WiFi and performed all necessary Windows Updates.


5: Copy the “wiTECH_Install” folder to the desktop.


6: Install the provided version Adobe AIR.


7: Install the provided version of Java.


8: Install wiTECH.


9: After you have finished installed everything, when you get popup messages from Windows Firewall to allow or block any applications, click “Allow”.


10: When you get a popup for AdobeAIR and Java to update, click cancel and do NOT update either AdobeAIR or Java.


11: Open “My Computer” and in the upper left of the window, click on “Organize” and then select “Folder and search options”.


12: Click on the “View” tab and under “Hidden files and folders” select the radio button for “Show hidden files, folders and drives”. Also, uncheck the option for “Hide protected operating system files (Recommended)” and then at the top of the window, click the “Apply to Folders” button.


13: Navigate to “C:\ProgramData\wiTECH\jserver\data\core\stubs” and you will find three installers.


14: Install the DRBIII Emulator stub.


15: Wait for a popup to appear that states the security certificate isn’t valid and click “OK” to allow the software update to proceed. Another popup will appear and the software update will run. After it completes, close the wiTECH window if it opens.


16: Install the Enhanced DRBIII emulator stub.


17: Again, wait for a popup to appear that states the security certificate isn’t valid and click “OK” to allow the software update to proceed. Another popup will appear and the software update will run. After it completes, close the wiTECH window if it opens.


18: Install the K-Line stub.


19: Again, wait for a popup to appear that states the security certificate isn’t valid and click “OK” to allow the software update to proceed. Another popup will appear and the software update will run. After it completes, close the wiTECH window if it opens.


20: Connect the MicroPod2 to the vehicle, then connect it to the computer.


21: A popup window will appear to install software. Click “OK”.


22: After it finishes, start wiTECH and wait for the screen to show up with the MicroPod2 and IP address of it. You will see a “Launch DRBIII” button in the lower right corner. Ignore it as they do not properly open the emulator.


23: Create a shortcut on the desktop and enter the following into the ‘Path” field.


24: Disable the LAN and WLAN network connections and never connect to the internet again.


25: Click on the shortcut and you’re set! The DRBIII emulator will open and give you the choice to select several different vehicles.


Note:Its procedure ONLY work with wiTech MicroPod 2 from


If you want us to install in the laptop ready for use,you can check the product link:

How to Update the wiADVISOR microPod


In order to ensure the Micropod II is working properly, it will be necessary to update it based on the latest software releases provided by Chrysler. If your microPod is at version 0.4.2, it will not communicate with wiADVISOR. You must perform an update to version 1.2.2 using the USB cable that came with the microPod (see below).


To update your microPod using the USB cable:
1. Connect the large end of the USB cable to a computer that has the wiTECH Diagnostic
Application already installed – Typically this is a computer in the shop.


2. Connect the small end of the USB cable to the microPod as shown below:


3. Once the microPod is connected via USB, a green light will come on. Open your Internet browser and type the IP address in the address bar at the top of your browser and hit Enter on your keyboard. The microPod interface will come up as shown


a. If the System Release shows any version besides 1.2.2 (red box on image above), then your microPod should update to the most current version if the wireless connection on the microPod is properly configured.
b. If the System Release version shows 0.4.2, the wireless connection on the microPod must be configured in order for the microPod to update. Please contact the wiADVISOR Team at 1-855-wiADVISOR for assistance with this process.
Once wireless is configured, simply wait until the light on the engine diagnostic tool microPod will begin to flash with slow bursts of red indicating that the microPod has started the update process. You will not be able to access the microPod during the update and will have to wait 4-6 minutes before it finishes. The flashing red light will return to green once the update is complete.

4. NEXT: Click on ‘Software Config’ (left side):


a. If the wiADVISOR version is 1.1.6, this needs an update. See below:


b. To update the App Version to 1.1.9, simply leave the microPod plugged into the PC. Pod will update itself. Refresh the screen until the version shows 1.1.9.

5. Now that your microPod System Release shows version 1.2.2, and the software shows an App version of 1.1.9, your microPod is now up-to-date.

Determining the Status of your microPod:
If you are not sure if your microPod requires an update, follow the below steps to confirm this. To view the current status of your microPod, you must be logged into the wiADVISOR application and have selected “Vehicle Queue” in the interface. When a microPod is powered up, the software status will be displayed along with connected vehicle information.

1. microPod Status Types – There are three types of update statuses av ailable for the microPod:

a. Up-to-date – This status indicates that your microPod is up-to-date and no further action is required at this time. If the software is up-to-date, no status information will
be displayed. Otherwise one of the following two scenarios will be shown.

b. Update Available – This status indicates that there is an update available for your microPod. It is highly recommended that you update your microPod at your earliest convenience. You may continue to use the microPod without updating it when this status appears.


c. Update Required – This status indicates that an update is required on the microPod in order to continue using it.


2. To update the software, disconnect the microPod from the vehicle and connect it to your computer using the USB cable (computer must have the OBD-II scan tool wiTECH Diagnostic Application installed).

3. Since your microPod is updated to the 1.2.2 System Release; once booted and no vehicle power is detected, the microPod will automatically begin the update process. Depending on what software is being updated, the process can take anywhere from a few seconds to several minutes. During this time the LED lights will blink red and off. Monitor the Vehicle Queue to determine if the update has completed.
Disconnecting the USB cable prior to update completion may leave the microPod in an irrecoverable failure state.
After powering up with the USB cable, the screen will warn you that the update is starting and you must not unplug the device until the update is complete (see below).


4. When the update is completed, the text in the Vehicle Queue will change indicating that microPod is up-to-date. At this time, it is safe to disconnect the USB ca ble and re-connect to a vehicle.

Troubleshooting Tips:
If you find that you are having issues with updating your wiADVISOR microPod there are few resolutions you can try.
1. Make sure you have wiTECH installed on the computer. (The microPod needs the wiTECH drivers in order to connect to the PC)
2. Try a different USB to mini USB cable.
3. Unplug the cable from the PC and try a different USB port.
4. Try a different PC; make sure you are in range of the wiADVISOR Access Point.

wiTECH MicroPod II v17.03.10 clone review Dodge Avenger 2014 OK

Just ordered a Chinese clone Chrysler Micropod II and it has been working exactly like an OEM unit. No errors so far and tested functions on 3 different vehicles. It has been confirmed working with unmodified software wiTECH v17.03.10 (downloaded directly from a blog, I put the site below) and online (logged into TechAuthority). Not sure if it will be blacklisted or the firmware will be upgradeable with the next software release, but for now it works fine.

I have also uploaded pictures of the internals for those who are curious.




The site I am using for this tool:

This version of Witech (17.03.10) works fine on Windows 7 and Windows 10.
on a 2014 Dodge Avenger just fine.

was able to flash a module update & program a new key with the unit

also, possible to use DRB III Emulator with it, DRB III emulator confirmed working.

So far, happy with this witech MicroPod 2.

How to install WiTech MicroPod 2 software 17.04.27 on Windows 7?

How to install Chrysler wiTech MicroPod 2 software 17.04.27 on Windows 7?

Step 1: install AdobeAIRInstaller.exe
Step 2: install jre-6u45-windows-i586.exe
Step 3: install wiTECH_Install_17.04.27.exe
Step 4: restart the computer

Pay attention:
The computer date must be set to that day. (The day you install WiTech MicroPod 2 17.04.27)
The computer must be connected to the Internet.
Connect the MicroPod 2 to computer to open the software.
When it pop up registration tips, turn off the software and turn it on  repeatedly then you can use it.

Which MicroPod 2 clone is tested 100% safe to use?
wiTech MicroPod 2
WiTech 17.03.10 OK
WiTech 17.04.27 OK
Chrysler wiTech MicroPod 2 Best Quality OEM
WiTech 17.03.10 OK
WiTech 17.04.27 Still testing
6-2 6-3

Tips: Difference between Chrysler Micropod II and Chrysler wiTech MicroPod 2 Best Quality OEM
Same: Internet connection OK, Chrysler online programming and diagnosis OK
Different: Chrysler wiTech MicroPod 2 Best Quality OEM is much better than wiTech MicroPod 2’s.
You get what you pay for from Hope it helps my friend!

How to install Chrysler wiTech MicroPod 2 Diagnostic Programming Tool?

WARNING; The computer on the day of the date

1.PC-Based: Requires PC connected to the network


2.Run Chrysler wiTech MicroPod 2 CD software as picture


3.Firstly, installation AdobeAIRInstaller.exe


4.Secondly, installation jre-6u45-windows-i586.exe


5. Finally, installation wiTECH_Install_17.03.10.exe


6.After successful to install the software, the desktop will appear Chrysler wiTech MicroPod 2 software icon is as follows:


7. The specific installation process, please watch the following installation video: