Program A New ECM Module to Nissan Murano with Consult 3

Background information:

A Nissan Murano Z51 3.5L CVT 2012Y  had an accident.  The lower part of the connectors of the original engine control unit moved by 7-8mm inside the board, half of the pins are broken off, one heating channel of the upper lambda does not work, although the field effect transistor is jerky. Got and most lambda, but it has already changed.

Bought a new ECM, there were no problems with snapping, software is different. The old module stands still, the new Nissan Consult III Plus lies on top:


Disclaimer: The tutorial was translated from Russian. Credit to Car-Buster. You are at your risk.

Marking the old ECM module: 23710-1AA4B
Marking the new ECM module:  23710-1TJ0A


Well visible recessed connectors:


Back of the control modules


During this procedure, all previously programmed keys are erased, so it is strongly recommended to register all keys at a time:

Device used:  original Consult-III diagnostic without the Immo card , and with the correct software:
If you using the clones, better go for Consult III Plus, Nissan Consult 3 Plus adds ECU programming function without working with immobiliser card since software version v65.12.


There are many step-by-step screenshots, so I’ll lay out the most basic.
After installing a new unit, the car naturally won’t start, there will be an active error due to mismatch of ID keys recorded in the ECM and Immo , in short, there is no sync P1611 ID DISCORD IMMU-ECM :


Yes, the ignition turns on, the starter turns but the car no start
Let’s go.
Turn off the ignition, turn on the emergency light, connect to the car, choose vehicle model Murano Z51 after 2010.v. and press the Select button :


Confirm the choice with the Confirm button , but now select Repair :
Click on the tablet (top left):

We drop down the list and select NATS :

Click Start :

In the menu that appears, click Pin Read and Next :

We get the PIN 14A06 , press END :

You also need the generic code Immo , in our case variant is 1211 :

After this, select STRG LCK RELES (KEY ID ERASE) , this procedure will erase the keys and pre-lock the steering column latch:

Enter the Immo code, 1211, and run the procedure:

Everything is carried out with the ignition off and with the emergency lights on. We hear how the steering column is unlocked, and the ignition is now turned on only when something (key) is inserted into the emergency key slot. And one more thing, the ACC mode disappears , this is normal, that is, immediately switch ignition OFF-ON and not like people OFF-ACC-ON :

The next step, turn on the ignition with any key, and in the NATS menu we already choose C/U Initialization :

Enter the immo code 1211, and go to the last screen, claiming that initialization is completed:
Turn off the ignition, take out the key (it has not yet been registered, but served only to start the procedure). Now we insert the first key into the slot, turn on the ignition, turn off the ignition, pull out the key, the immo indicator flashes 5 times. Repeat this procedure for keys 2-5.
In my case, only 2 keys. Turn off the ignition, check the operation of the radio channel from each key. Works. Now remove the first key away from the car, and leave the second inside, start the engine – with a half kick. For the second key is similar.
As a result, there is no error in heating one of the upper lambda, and in the current data adequate readings. Engine speeds develop adequately without kicks. New engine control module was replaced successfully.

How to use Nissan Consult III do ECU programming

I try to program a new blank engine ECM on a 2013 Nissan Armada. I purchased the software file from Nissan website and one Consult-3 Plus. I do not have Consult online synchronized with Assist. At first, I have no idea what folder to put this file in so Consult program will find.

I used ners and nissan file extracted to correct folders by itself. used unpack.exe. anyway here you go 6) For CONSULT III plus “Blank” ECU (ECM and non-IK TCM) Programming

Note 1: Before using this application, you will need to put the “programming” data file (*.dat) and the management csv file you received with the download, in the C:\ReproProgramming folder (see screen capture

above under item # 5). Without the programming data and the management csv file in this folder, the C-III plus application will not identify or display the applicable programming. The Auto diagnostic tool C-III plus software will check the part number of the ECU on the vehicle and display the reprogram to be installed.

NOTE 2: If this is the first time using C-III plus for reprogramming, you may need to make the C:\ReproProgramming folder. C-III plus does not automatically create the folder.

How to get Nissan Consult 3 Software to Work with Jdiag Elite J2534

– Is the Jdiag Elite J2534 compatible with Nissan Consult III Plus 2017 the latest software?

– Yes, definitely. It works perfect with Nissan consult III Plus software, already tested with many Nissan cars.

So, how to setup Jdiag Elite J2534 to work with Nissan consult 3 Plus?

Here you go.

The main steps…

Open Consult iii Plus Software on Desktop

Connect JDiag Elite to the laptop USB and OBDII cable to the OBDII port on the car

Choose JDiag hardware

Choose the signal module to read out information

Then work with it

Then the details for you…

Open Nissan Consult 3 Plus software

Connect JDiag Elite J2534 device to the laptop USB and OBDII cable to the OBDII port on the car

Select VI/MI in Consult 3 Plus ver.52.11


Select VI and click on Connect


Then Close


You’ll see the connection status: VI: Normal module/USB connection
Start Diagnosis (one system)


Choose a module to read out info

Also, you can choose by the car type

Back and start Diagnosis (all system)

Consult 3 plus Nissan car list

Consult 3 plus Infiniti car list

Manual selection

Choose a model and the model year

Automatic selection


Consult-3 Plus for Nissan is the newest Nissan diagnostic tool

Nissan Consult III Plus is the newest Nissan diagnostic tool.
1. Nissan Consult III Plus supports Nissan 2016 MY LEAF Quest and Murano Cross Cabriolet,
2.super racing MY GT-R and 2012 of NV and 2012 MY Infiniti M and M Hybrid from 2011/12.
3.Consult-3 Plus for Nissan= Consult-3 + Consult-2

Consult-3 Plus for Nissan Consult 3 V61.10 diagnostic tool for Nissan from OBD2TOOL
Consult-3 Plus for Nissan= Consult-3 + Consult-2
Software Version: V61.10
C3+ GTR software V20.11
This Consult-3 Plus work for 2016 Nissan
Support Multi-Languages: English, French, German, Portuguese, Italian, Japanese, Finnish, Greek, Russian, Spanish, Turkish, TChinese(Simplified), Chinese(Traditional)
Communication Mode: USB 2.0 / Bluetooth
OS Requirement: Work with Windows XP,WIN7 WIN8 WIN10
Support Electronic control module Programming,If you want to key programming, please buy the Security Card for Immobilizer
V61.10 Software Download:!aUR3BaxB!ZL3WccsZn–wG8xIirSzgqlZiEkgyxDRen9MrugEr-w

Nissan Consult 3 Plus Function:
Consult-3 Plus for Nissan can support all the models of the Nissan and Infiniti from 1996 up till now, with all Consult II & III functions .
And consult III plus can calcaulate the password for the new cars till year 2016 with NISSAN Password.
1. Consult-3 plus (consult 3+) work for all nissan car , infiniti car and for nissan gtr car to 2016.
2. Consult-3 plus work with obd-16 connector for the new kind of car, work with 14 pin connector for the old kind of car.
3. Consult-3 plus support for nissan car electrolic system diagnostic.
4. Consult-3 plus support for nissan electromobiles such as Leaf.
5. Consult-3 plus support all Renault.

Conslu-3 for Nissan Functions:
1. Scantool Diagnostics:for all Nissan,Infiniti,GTR
2. Immobi and Smart key:for all Nissan,Infiniti,GTR
3. Nissan GTR: for Nissan GTR Diagbostics and Immobi
4. Electromobiles car:for Nissan Electromobiles car Diagbostics and Immobi

Conslu-3 for Nissan Packing List:
1pc* Consult 3 Plus for Nissan Vehicle Communication Module + OBD16 Cable
1pc* 14Pin Line for Nissan
1pc* USB 2.0 Cable
1pc* Bluetooth
1pc* Power Supply
1pc* Casebox